Last modified by writer on 2024/09/25 14:21

From version 1.7
edited by writer
on 2024/09/24 13:44
Change comment: There is no comment for this version
To version 2.1
edited by writer
on 2024/09/24 14:01
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -23,7 +23,7 @@
23 23  Please note that the rotary axis chuck motor and the rollgang motor are tied to the same rotary axis B.
24 24  {{/warning}}
25 25  
26 -For the convenience of further configuration, we will rename the rotary axis motors to “Holder” and “Rollgang”.
26 +For the convenience of further configuration, we will rename the rotary axis motors to “Chuck” and “Rollgang”.
27 27  
28 28  [[Motors Settings>>image:image2020-8-26_7-52-11.png||data-xwiki-image-style-alignment="center" height="548" width="1000"]]
29 29  
... ... @@ -36,23 +36,24 @@
36 36  The "SPU" parameter in this block must be calculated in such a way that when the G0 B360 command is issued, the rotary axis chuck makes exactly one revolution. The rollgang rotation will be calibrated in the following steps.
37 37  {{/success}}
38 38  
39 -Когда основные характеристики оси были настроены, перейдем к заданию расширенных параметров двигателя для рольганга. Для этого в правой части окна настроек осей обратимся к блоку "Дополнительные возможности".
39 +Let's move on to setting advanced motor parameters for the rollgang when the basic characteristics of the axis have been configured. To do this, in the right part of the axes settings window, turn to the “Additional features” block.
40 40  
41 -Из выпадающего списка необходимо выбрать двигатель, который подключен к рольгангу.
41 +From the drop-down list you must select the motor that is connected to the rollgang.
42 42  
43 -Установите отметку на опции "Приводной рольганг" чтобы "сказать" системе, что этот двигатель находится в составе рольганга.
43 +Check the "Motor as  Rollgang" option to "tell" the system that this motor is part of the rollgang.
44 44  
45 -Основная идея автоматического управления приводным рольгангом в PUMOTIX заключается в следующих пунктах:
45 +The basic idea of ​​automatic rollgang control in PUMOTIX is the following points:
46 46  
47 -1. Поворотная ось (A или B) одна, а двигателей, привязанных к поворотной оси может быть несколько (например, патрон и приводной рольганг).
48 -1. Скорость F и расстояние перемещения (например, G0 B720) задается для поворотной оси, а не для двигателя рольганга.
49 -1. Скорость вращения рольганга должна рассчитываться автоматически исходя из трех параметров:
50 -11. диаметра ролика рольганга;
51 -11. количества импульсов STEP для поворота ролика на 1 градус;
52 -11. диаметра трубы, установленной на рольганг.
47 +1. There is only one rotary axis (A or B), but there can be several motors attached to the rotary axis (for example, a chuck and a rollgang).
48 +1. The speed F and moving distance (for example, G0 B720) are set for the rotary axis, not for the rollgang motor.
49 +1. The rollgang rotation speed should be calculated automatically based on three parameters:
50 +11. rollgang roller diameter;
51 +11. count of STEP pulses to rotate the roller by 1 degree;
52 +11. diameter of the pipe installed on the rollgang.
53 53  
54 -{{info title="**Основной принцип работы поворотной оси с приводным рольгангом**"}}
55 -При изменении диаметра трубы, установленного на рольганг, автоматически должна изменяться скорость вращения роликов рольганга. При этом скорость вращения патрона поворотной оси остается неизменной. Чем больше диаметр трубы, тем больше скорость вращения роликов рольганга и наоборот.
54 +{{info title="**The basic operating principle of a rotary axis with a rollgang**"}}
55 +The rotation speed of the rollgang rollers should automatically change when changing the diameter of the pipe installed on the rollgang. In this case, the rotation speed of the rotary axis chuck remains unchanged.
56 +The larger the diameter of the pipe, the greater the rotation speed of the rollgang rollers and vice versa.
56 56  {{/info}}
57 57  
58 58  Для того, чтобы система могла автоматически рассчитать поправочный коэффициент для связи диаметра трубы со скоростью вращения роликов, необходимо внести в настройки системы следующие данные: