Last modified by writer on 2024/05/14 13:56

From version 4.1
edited by writer
on 2024/05/14 13:39
Change comment: There is no comment for this version
To version 6.1
edited by writer
on 2024/05/14 13:56
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -1,10 +1,6 @@
1 -{{info}}
2 -**This page didn't translate yet. You can see the original page.**
3 -{{/info}}
4 -
5 -1. **Используя прилагаемый инжектор питания, подключите пульт согласно схеме, приведенной ниже.**
6 -При правильном подключении светодиоды выбора оси должны загореться. Это говорит о том, что пульт включен, но пока не имеет связи с управляющей программой.[[image:PLCM-R1.png||data-xwiki-image-style-alignment="center" height="400" width="513"]](((
7 -
1 +1. **Using power injector connect the pendant according to the diagram below.**
2 +The axis selection LEDs should light up if connected correctly. This indicates that the remote control is turned on, but is not yet in contact with the control program.(((
3 +[[image:PLCM-R1_en.png||data-xwiki-image-style-alignment="center" height="400" width="513"]]
8 8  )))
9 9  1. (((
10 10  **Run PUMOTIX.**
... ... @@ -27,12 +27,11 @@
27 27  [[image:PLCM-R1_setup_window.png||data-xwiki-image-style-alignment="center" height="655" width="900"]]
28 28  )))
29 29  1. (((
30 -**Установите связь между компьютером и пультом.**
31 -Если вы настроили пульт, но продолжают гореть все светодиоды осей, необходимо изменить сетевые настройки PLCM-R1. (% style="letter-spacing:0.0px" %)Для этого воспользуйтесь кнопкой настроек в правом верхнем углу окна.(%%)
26 +**Establish a connection between the PC and the pendant.**
27 +If you have configured the pendant but all the axis LEDs continue to light, you will need to change the PLCM-R1 network settings. Use the settings button in the upper right corner of the window to do this.
32 32  [[image:PLCM-R1_setings_child_window.png||data-xwiki-image-style-alignment="center" height="267" width="350"]]
33 33  
34 -В появившемся окне установите IP-адрес в одной подсети с вашим компьютером (например, если адрес компьютера 192.168.10.5, маска 255.255.255.0, установите, например, 192.168.10.23, маска 255.255.255.0, или любой другой свободный адрес). Нажмите “Применить”.
35 -После применения настроек, на пульте загорится светодиод Connect.
36 -
30 +Set the IP address the same subnet with your PC (example: PC IP address is 192.168.10.5, mask 255.255.255.0, set the pendant IP address 192.168.10.23, mask 255.255.255.0, or another free IP address). Press the "Apply".
31 +After setting applying pendant LED "Connect" will light up.
37 37  )))
38 -1. **Закройте окно настройки - пульт готов к работе.**
33 +1. **Close the settings window - your pendant is ready to use.**