Wiki source code of Настройка PLCM-R1
Last modified by writer on 2024/05/14 13:56
Hide last authors
| author | version | line-number | content |
|---|---|---|---|
 |
20.1 | 1 | 1. **Using power injector connect the pendant according to the diagram below.** |
| 2 | The axis selection LEDs should light up if connected correctly. This indicates that the remote control is turned on, but is not yet in contact with the control program.((( | ||
| 3 | [[image:PLCM-R1_en.png||data-xwiki-image-style-alignment="center" height="400" width="513"]] | ||
| |
7.1 | 4 | ))) |
| |
3.1 | 5 | 1. ((( |
| |
20.1 | 6 | **Run PUMOTIX.** |
| 7 | Open Plugins Configuration window via menu "Plugins" → “Plugins Configuration” and set the "Active" sign for plugin "CNC pendants". | ||
| |
3.1 | 8 | |
| |
20.1 | 9 | [[image:Pednant plugin On.png||data-xwiki-image-style-alignment="center" height="200" width="584"]] |
| |
3.1 | 10 | |
| |
20.1 | 11 | After that open the CNC pendants window for PLCM-R1 setup via "Plugins" menu. |
| |
7.1 | 12 | |
| |
20.1 | 13 | [[image:CNC pendant menu.png||data-xwiki-image-style-alignment="center" height="100" width="400"]] |
| |
3.1 | 14 | ))) |
| 15 | 1. ((( | ||
| |
20.1 | 16 | **Setup the PLCM-R1 with PUMOTUX using the plugin.** |
| 17 | Select the pendant on the "Selected device" field. The list of devices is loaded automatically depending on the pendants connected to the PC. | ||
| 18 | You must make a selection in the “Selected profile” field to configure the pendant. The list of profiles is loaded automatically depending on the selected module. PUMOTIX comes with default PLCM-R1 configurations but you can also create a custom configuration. | ||
| |
3.1 | 19 | |
| |
20.1 | 20 | [[image:Empty Pendant plugin Window.png||data-xwiki-image-style-alignment="center" height="464" width="900"]] |
| |
7.1 | 21 | |
| |
20.1 | 22 | Next you will see on your screen the model of pendant and fields with commands for pendant buttons. Setup the pendant and press the "Apply" button. |
| 23 | [[image:PLCM-R1_setup_window.png||data-xwiki-image-style-alignment="center" height="655" width="900"]] | ||
| |
3.1 | 24 | ))) |
| |
4.1 | 25 | 1. ((( |
| |
20.1 | 26 | **Establish a connection between the PC and the pendant.** |
| 27 | If you have configured the pendant but all the axis LEDs continue to light, you will need to change the PLCM-R1 network settings. Use the settings button in the upper right corner of the window to do this. | ||
| 28 | [[image:PLCM-R1_setings_child_window.png||data-xwiki-image-style-alignment="center" height="267" width="350"]] | ||
| |
3.1 | 29 | |
| |
20.1 | 30 | Set the IP address the same subnet with your PC (example: PC IP address is 192.168.10.5, mask 255.255.255.0, set the pendant IP address 192.168.10.23, mask 255.255.255.0, or another free IP address). Press the "Apply". |
| 31 | After setting applying pendant LED "Connect" will light up. | ||
| |
4.1 | 32 | ))) |
| |
20.1 | 33 | 1. **Close the settings window - your pendant is ready to use.** |