Skip to Content
Last modified by writer on 2023/08/03 19:55
From version 2.1
edited by writer
on 2022/08/25 13:30
Change comment: There is no comment for this version
To version 3.1
edited by writer
on 2022/08/25 13:43
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -28,7 +28,7 @@
28 28  4
29 29  )))|(((
30 30  ER-00013100
31 -)))|Quick start G-Code from an arbitrary line|(% style="width:650px" %)The time spent on preparing the trajectory planner to run from an arbitrary line will be significantly less. The larger the file, the greater the effect of this feature. Recommended for milling machines.
31 +)))|Quick start G-Code from an arbitrary line|The time spent on preparing the trajectory planner to run from an arbitrary line will be significantly less. The larger the file, the greater the effect of this feature. Recommended for milling machines.
32 32  |(((
33 33  5
34 34  )))|(((
... ... @@ -38,12 +38,12 @@
38 38  6
39 39  )))|(((
40 40  ER-00013099
41 -)))|Continuation of the G-Code from the middle of the trajectory (frame)|(% style="width:650px" %)The feature allows you to resume the execution of the control program directly from the place where it was stopped by the STOP command or by the operation of special inputs, such as a "sensor for the door of the protective cabin" or "metal touch sensor with a plasma torch." In this case, the machine makes a regular (non-emergency) stop and the coordinates of the stop point are remembered. After that, you can move the machine as you like, including adjusting it to a convenient place and removing chips from the cutter or completely replacing it. Now just press “Start” and the machine itself will return to the stopping point and continue to execute the G-Code. In this case, the return to the starting point of execution will be made according to the selected [[mode of return to the trajectory>>doc:Руководство пользователя.Особенности функционирования системы.Выполнение подготовительного перемещения.WebHome]].
41 +)))|Continuation of the G-Code from the middle of the trajectory (frame)|(The feature allows you to resume the execution of the control program directly from the place where it was stopped by the STOP command or by the operation of special inputs, such as a "sensor for the door of the protective cabin" or "metal touch sensor with a plasma torch." In this case, the machine makes a regular (non-emergency) stop and the coordinates of the stop point are remembered. After that, you can move the machine as you like, including adjusting it to a convenient place and removing chips from the cutter or completely replacing it. Now just press “Start” and the machine itself will return to the stopping point and continue to execute the G-Code. In this case, the return to the starting point of execution will be made according to the selected [[mode of return to the trajectory>>doc:Руководство пользователя.Особенности функционирования системы.Выполнение подготовительного перемещения.WebHome]].
42 42  |(((
43 43  7
44 44  )))|(((
45 45  ER-00013094
46 -)))|G-Code runtime calculation|(% style="width:650px" %)This feature allows you to calculate the time remaining until the end of the G-Code. It takes into account the dynamics of the machine and the interpolation algorithms that will be used during operation, which allows to achieve high accuracy of calculations. In addition, the remaining time is instantly recalculated if the user adjusts the feed rate or idle speed during operation.
46 +)))|G-Code runtime calculation|This feature allows you to calculate the time remaining until the end of the G-Code. It takes into account the dynamics of the machine and the interpolation algorithms that will be used during operation, which allows to achieve high accuracy of calculations. In addition, the remaining time is instantly recalculated if the user adjusts the feed rate or idle speed during operation.
47 47  |(((
48 48  8
49 49  )))|(((